TENAX POLYESTER GLUE
Flowing Transparent and White-For Horizontal Repair, glue, and fill. Knife Grade Transparent & White-Vertical Repair, glue, and fill. Surface must be clean and DRY. Separate Hardener is added to activate. Mix by weight, not volume. 100 grams of resin requires 3 grams of hardener. Gel time is 7-8 minutes. (Flowing White is 3-4 minutes) Quart Can.
TENAX CRYSTAL KNIFE GRADE
Clear Acrylic/Polyester mix Epoxy designed for laminating stone. Color can be added to match any stone and will appear to be a transparent type coloring for a better blend. Surface must be clean and DRY. Mixed by weight. 100 grams of resin with 2-4 grams of hardener. Very important for proper strength and color. Use only the hardener designated for Crystal. Too much hardener will speed the process, but will cause a yellowing effect. Available in Quart cans.
TENAX CRYSTAL LIQUID
Flowing Clear Acrylic/Polyester mix Epoxy designed for FILLING and laminating stone. Color can be added to match any stone and will appear to be a transparent type coloring for a better blend. Surface must be clean and DRY. Mixed by weight. 100 grams of resin with 2-4 grams of hardener. Very important for proper strength and color. Use only the hardener designated for Crystal. Too much hardener will speed the process, but will cause a yellowing effect. Available in Quart cans.
TENAX EE-10
Specialized penetrating epoxy for filling in all cracks and defects. This epoxy is applied to clean DRY stone after the 120 grit stage of polishing process. Once complete hardening is achieved, 120 grit is used to remove the epoxy from surface. Complete hardening will depend on which hardener is used. This will give the stone strength and a darker finish. Clear flowing type for granite and marble. Available in Quarts.
HARDENER FOR EE-10
#18/25
Hardener for large grain pitted stone with small cracks.
#11/25
This mesh matting is for thin stone slabs that are fragile and may be easy to break. Mesh openings are about 1/4" square. Applied with EE-10 Epoxy and 18/25 Hardener. Matting is 5' wide and is sold per linear meter(39").
Hardener for tight grain stone with micro-fissures.
TENAX RIVO-50 A AND B
Use for granite, marble, and stone of all types when a strong bond and a faster setting time is required. Will bond to almost any clean DRY surface. Polished surfaces will need to be honed for best results. Interior and Exterior. Gel time in about 50 minutes. Complete hardening in about 12 hours. In colder temperatures (below 40 degrees F), reaction will be slower. Store at room temperature. See Tepox for coloring. Mix as 50/50 of part A and part B. Has an off white color. Knife grade. Kit is a quart of each, Part A and Part B. (Part A and Part B can not be sold separately.)
STONE EPOXY
TENAX DOMO-10 A & B
Use for granite, marble, and stone of all types that need to be bonded. Our strongest epoxy. Will bond to almost any clean surface, even if moist. Polished surface will need to be honed for best results. Interior and Exterior. Gel time in about 3 hours. Complete hardening in about 12 hours. In colder temperatures (below 40 degrees F), reaction will be slower. Store at room temperature. See Tepox for coloring. Mix 50/50 of part A and part B. Has an off white color. Knife grade. Kit is a quart of each, Part A and Part B. (Part A and Part B can not be sold separately.) Also available is a special designed caulking cartridge containing both Part A and Part B with two mixing nozzles. Extra nozzles available.
TENAX MICTO A AND B
Use for granite, marble, and stone of all types that need a strong bond and a very fast setting time. Will bond to almost any clean DRY surface. Polished surfaces will need to be honed for best results. Interior & Exterior. Gel Time in about 5 minutes. Complete hardening in about 12 hours. In colder temperatures (below 40 degrees F), reaction will be slower. Store at room temperature. Mix as 50/50 pf part A and B by WEIGHT. Is a clear flowing type. Kit is a quart of each, Part A and B. (Part A and Part B can not be sold separately.)
